Kodak D76 Black & White Developer (Makes 3.8L)
Kodak D76 Black & White Developer (Makes 3.8L)
$12.00
KODAK Developer D-76 provides full emulsion speed and excellent shadow detail with normal contrast, and produces fine grain with a variety of continuous-tone black-and-white films.
– Classic black & white developer.
– Powder sachet, just mix with water.
– Makes 3.8L of developer (1 US Gallon)
– Brand new, direct from Kodak
– For further info, check out the Kodak Data sheet here.
This item can not be shipped via Express Services.
This item can not be shipped outside of Australia.
Out of stock
){kind=link}
Additional information
| Weight | 430 g |
|---|---|
| Brand | Kodak |
| upc | |
| MPN | 5160296 |
Sold out
Quickview
Kodak XTOL Black & White Developer (Makes 5L)
Film Processing Chemicals
KODAK Professional XTOL Developer is a two-part powder developer for processing KODAK and other manufacturers’ normally exposed, pushed, or pulled black-and-white films.
It offers full emulsion speed and easy mixing, and can be used as both a developer and a replenisher in a variety of equipment, from small tanks, trays, or rotary tubes to high-volume processors.
- Easy mixing at room temperature
- 2 part powder, just mix with water.
- Makes 5L of developer (1.32 US Gallons)
- Brand new, direct from Kodak
- Long lasting
- No nasty hydroquinone
- Good shelf life
- For further info, check out the Kodak Data sheet here.
This developer chemical is not a dangerous or hazardous good, and thus can be shipped normally as any other item.
$20.00
Quickview
$12.00
MFS Remjet Remover Solution
Film Processing ChemicalsThis solution is used to soften the Black RemJet layer of Motion Picture Film ready for removal and then development with home C-41 chemistry.
To test the solution, cut the leader/piece of film off and dip in the solution for 10 seconds. Rinse film under running water and the RemJet should wash away. Perfect for use on MFS vision3 films!
Contains:
2x Remjet Remover kit to make 500ml Solution
Quickview
CineStill Df96 Black & White Processing Chemicals
Film Processing Chemicals
IN STOCK NOW!
For easy at-home black and white film processing!
These easy to use black and white processing chemicals from Cinestill can process 16+ rolls of film per litre, just using the one chemical!
Develop anywhere between 20-28°C.
The worries of too much development, dilution, time or agitation are gone. Stop bath? Fixer? Hardener? Gone the way of One-Hour-Photos and formaldehyde.
The single-step solution is now available in this easy to use powder concentrate.
Processing all of your B&W film at home is easier than ever with this magical and versatile Single-Step BW “Developer-Fix” monobath solution, akin to D96 motion picture developer but with no need for stop bath, fixer, or any other chemicals, is perfect for processing CineStill BwXX along with any other black & white film.
No special charts, timers or apps needed! Just a processing tank and water. Foolproof self-completing process that guarantees motion picture quality, the smoothest grain structure and crisp tonal curve. Flexible processing in 3-6 minutes at any room temperature (20-28°C). Just wash with water and hang to dry. No more complicated measurements or strict margins to deal with. Process all your black and white films in one chemical with absolutely wonderful results!
- Processing for traditional B&W film in 1 bath
- Room temperature processing methods for 20-28°C
- Temp tolerance is +/-1°C
- Worlds fastest process at 27°C in just 3min!
- Push/Pull processing by adjusting temp. +/- 6°C
- Reusable, all-in-one solution.
- Processes over 16+ rolls of film (per 1000ml)
- Process 1-8 rolls at a time
- Extremely versatile self-completing process
- No special processor needed (use standard processing tanks and reels like Paterson Tanks)
- Fully archival
- Odour-free
$45.00
Quickview
$7.00
Ilford Simplicity Wetting Agent – Single Pack
Film Processing Chemicals- For 8x 120 or 16x 35mm Rolls of Film
- ILFOTOL Wetting Agent
- Reduces Water Spots on Film
- Used During Final RinseThe Ilford Simplicity Wetting Agent is non-ionic wetting agent used as a final rinse before drying films. It can be used in all manual and machine processes to greatly reduce the risk of drying marks being formed. It can also be used as a final rinse before drying fibre based prints to provide rapid, even drying.
How to Use
Simply pour the full contents of the dev, stop and fix sachets into separate measuring containers, dilute each one to 600ml with water at the correct temperature, stir to ensure they are mixed and then you are ready to use as part of the normal dev, stop, fix and wash sequence. At the end of the wash sequence add 2 cap-fulls of the wetting agent to the tank and give five inversions before removing the films.